perle-logoPerle LogoPerle Logo
  • Global - English

    • Deutsch

    • Français

    • Italiano

    • Español

    • 日本語

    • 中國

  • Contact Us
  • PRODUCTS
      • Serial to Ethernet
        Connect serial based equipment across an Ethernet LAN:
      • Serial Terminal Servers
        Connect Serial RS232 ports over Ethernet
      • Serial Console Servers
        Connect to Cisco and Data Center Equipment
      • Serial Device Servers
        Network enable RS422 and RS485 Devices
      • Ethernet I/O
        Access & Control remote Digital IO, Analog IO, relays & sensors
      • Serial Extenders
        Extend Serial data transmissions over long distance
      • Serial to Fiber
        Extend RS232, RS422 and RS485 over optical fiber
      • Serial SHDSL Extender
        Transmit serial data up to 20 km across copper wire
      • RS232 Serial Isolator
        Electrical isolation of RS-232 (V.24) interfaces
      • Serial Interface Converter
        Convert RS232 to RS422 or RS485
      • RS485 Repeater
        Amplify RS485 signals up to 1.2km
      • Media Converters
        Extend network distances over fiber up to 160km
      • Copper to Fiber
        Extend 10/100/1000/10G copper-based Ethernet equipment over fiber
      • Fiber to Fiber
        Connect multimode to multimode or multimode to single mode
      • Specialized Converters
      • Modular Chassis System
      • Stand-alone Media Converters
      • Managed Media Converters
      • SFP Media Converters
      • PoE Media Converters
      • Industrial Converters
      • DIN Rail Mounted Converters
      • SFP to SFP Protocol Transparent
      • PerleVIEW Device Management Software
        Centralized management for Perle Media Converters, Ethernet Extenders and Industrial Switches
      • Ethernet Extenders
        Transparently extend 10/100/1000 Ethernet connections across copper wiring
      • Ethernet Repeater
      • 10/100 Copper Extenders
      • 10/100/1000 Copper Extenders
      • Modular Chassis System
      • Stand-alone Copper Extenders
      • Managed Ethernet Extenders
      • Industrial Ethernet Extenders
      • PoE Ethernet Extenders
      • SHDSL Ethernet Extender
      • Remote Power Switches
        Remotely power on/off/cycle Data Center equipment
      • PCI Cards
      • Serial Cards
        Add RS232, RS422, RS485 serial ports to your PC or server
      • Parallel Cards
        Add IEEE 1284 parallel ports standard to your PC or servers
      • Industrial Switches
        Compact Industrial-grade Ethernet Switches designed for harsh temperature, vibration and shock environments
      • Managed Industrial Switches
      • Unmanaged Industrial Switches
      • PoE Switches
      • SFP, SFP+ and XFP Optical Transceivers
      • SFP Optical Transceivers
      • SFP+ and XFP Optical Modules
      • DIN Rail Power Supplies
        5, 12, 15, 24, or 48 V DC Industrial-grade reliability
      • PoE & PoE+ Injectors
        Integrate PoE devices into a non-PoE network
      • Surge Protectors
        Effective lightening, RFI and transient surge protection
      • CAT5/6/7 Surge Protector
        Protect wired, wireless and PoE equipment at speeds up to 10Gbps
      • SHDSL Surge Protector
        Protect DSL telecommunication interfaces
  • APPLICATIONS
      • Industry User Stories
      • Telecommunications
      • Healthcare and Medical
      • Government / Military
      • Data Center Management
      • Electric Utilities
      • Renewable Energy
      • Oil & Gas
      • Industrial Automation
      • Marine
      • Finance
      • Education
      • Retail / Point of Sale (POS)
      • Transportation
      • Sports & Entertainment
      • Broadcasting
      • Resources
      • Online Product Demos
      • About Serial to Ethernet
      • Serial to Ethernet Terminology
      • About Ethernet over Fiber
      • About Fiber to Fiber Conversion
      • Documents
      • Technical Notes
      • Application Notes
      • Case Studies
      • White Papers
  • HOW TO BUY
      • Online Stores
      • USA Store
      • Canada Store
      • UK Store
      • European Store
      • Contact Perle
      • Contact Perle Sales
      • Get a Quote
      • Product Questions
      • Distributors
      • USA Distributors
      • Worldwide Distributors
  • SUPPORT
      • Maintenance
      • Maintenance Options
        • America
        • EMEA
      • Maintenance Registration
      • Maintenance Inquiries
      • Warranty
      • Perle Product Warranties
      • Country Warranties
      • Warranty Registration
      • RMA Request
      • Technical Support
      • Request Support
      • Downloads
      • Knowledgebase
      • Cabling
      • Declarations of Conformity
  • ABOUT PERLE
      • Partners
      • Alliances
      • OEM Program
      • Enviromental Policy
      • REACH, RoHS & WEEE
      • Conflict Minerals
      • ISO 9001 & EMS 14001
      • Privacy & Cookie Policy
      • News & Events
      • Press Releases
      • Industry News
      • Media Contacts
      • About Us
      • Company
      • Contact Us
      • Careers
      • Certifications
      • Worldwide Offices

Products

  • Industrial Switches
  • Media Converters
  • Ethernet Extenders
  • Management Software
  • SFP & XFP Transceivers
  • DIN Rail Power Supplies
  • PoE & PoE+ Injectors
  • Surge Protectors
  • Console Servers
  • Device Servers
  • Terminal Servers
  • Ethernet I/O
  • Remote Power Switches
  • Serial to Fiber
  • Serial SHDSL Extender
  • RS232 Serial Isolator
  • RS232-RS485 Converter
  • RS485 Repeater
  • Serial Cards
  • Parallel Cards
  • Serial to Ethernet
  • Fiber to Ethernet
  • Fiber to Fiber

Applications

  • User Stories
    • Telecommunications
    • Healthcare and Medical
    • Government / Military
    • Data Center Management
    • Electric Utilities
    • Renewable Energy
    • Oil & Gas
    • Industrial Automation
    • Marine
    • Finance
    • Education
    • Retail / Point of Sale (POS)
    • Transportation
    • Sports & Entertainment
    • Broadcasting
  • Technical Notes
  • Application Notes
  • Case Studies
  • White Papers
  • Demos
  • How To Buy
  • Support
  • About Perle

How To Buy

  • Contact Perle Sales
  • Get a Quote
  • Product Question?
  • USA Distributors
  • Worldwide Distributors
  • USA Online Store
  • Canada Online Store
  • UK Online Store
  • European Online Store

Support

  • Technical Support
  • Knowledgebase
  • Downloads
  • Cabling
  • Declaration of Conformity
  • Warranty
  • Country Warranties
  • Warranty Registration
  • RMA Request
  • Maintenance Options
    • Americas
    • Europe
  • Maintenance Registration
  • Maintenance Inquiries

About Perle

  • Company
  • Contact Us
  • Careers
  • Certifications and Conformity
  • Privacy & Cookie Policy
  • Environmental Policy
    • REACH, RoHS & WEEE
    • Conflict Minerals
    • ISO 9001 & EMS 14001
  • News & Events
    • Press Releases
    • Industry News
    • Media Contacts
  • Partners
    • Alliances
    • OEM Program
  1. Products
  2. Ethernet Extenders
  3. 10/100/1000 Ethernet Extenders
  4. PoE Ethernet Extenders
  5. eXP-S1110 PE
  6. Print Friendly Version of this pagePrint Get a PDF version of this webpagePDF

eXP-S1110PE PoE+ Gigabit Ethernet Extenders

10/100/1000 PoE+ Ethernet Copper Extenders

10/100/1000 PoE+ Ethernet Extenders
  • Extends 10/100/1000Base-T up to 10,000 feet ( 3 KM )
  • Power remote PoE+ devices across 2-wire twisted pair or coaxial cable
  • On-board PoE power controller for true compatibility with IEEE 802.3af standard
  • High-Speed – up to 200 mbps aggregate line rate
  • Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes
  • Unique PD Reset feature enables a central site to reset the remote PoE device without a truck roll
  • Advanced features: Link Pass-Through*, Interlink Fault Feedback*, Auto-MDIX and Loopback, Plug and Play - Auto configuration of VDSL
Get a quote Bookmark this page
  • Overview
  • Hardware Specs
  • Application Diagrams
  • Documentation
  • Ordering Details

Perle eXP-S1110PE PoE+ Gigabit Ethernet Extenders transparently extend Ethernet beyond the general IEEE 802.3at limits of 328ft / 100m while providing Power over Ethernet ( PoE+ ) to standards-based compliant devices such as IP cameras, VoIP phones and wireless access points.

This technology enables users to transparently extend up to four 10/100/1000 Power over Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ), coax or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.

These PoE+ Ethernet Extenders are classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle eXP-S1110PE PoE Ethernet Extenders provide up to 30 watts of power to Powered Devices (PDs). Learn more about PoE.

These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments, and connecting a remote office or private-network backbone to a corporate LAN … anywhere you need 10/100/1000 Ethernet communication links for PoE+ devices up to 10,000ft (3KM) in distance.

Perle’s advanced features such as Link Pass-Through* and Interlink Fault Feedback*, Loopback and remote PD reset*, enable Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eXP-S1110PE PoE+ Gigabit Ethernet Extenders are also available with support for PoE.

eXP-S1110PE PoE+ Gigabit Ethernet Extender Features

Extend Ethernet over twisted pair Extend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km )
Extend Ethernet over Coaxial cable Extend an Ethernet link over 75 ohm coaxial cable
On-board PoE Power Controller As a fully compliant IEEE 802.3af and 802.3at PSE end-span device, this Ethernet Extender’s PoE power controller provides compliant power provisioning and monitoring, properly sensing through signature detection whether or not the attach Ethernet devices are PoE capable or not. This provides a safe connection for both PoE and Non-PoE capable devices.

Competitive PoE Ethernet Extender products operate as a simple passive power injector and will always apply power to RJ45 port pins which may result in damage if non-PoE compliant Ethernet devices are accidently attached.

Click here for more details
Advanced Power capabilities
  • ALT A/B and legacy PoE/PoE+ RJ45 pin selection
  • Current limiting protection
  • Remote PD reset
Fully compliant 802.3af PoE and 802.3at POE+ PSE
  • Enable/Disable PSE power
  • PD signature detection
  • Over-Current Protection
  • PD power classification detection ( Class 0,1,2,3,4 )
PSE Status Indicator A multi-color LED provided presents the status of the PSE function for easy troubleshooting of power over Ethernet connections
PD Power Reset ( Port 1 ) Ideal for remotely resetting equipment, this configurable function performs a momentary power reset to the attached Powered Device (PD) on Port #1.

Read our PD Reset Tech Note for further details on this feature
Broadest range of PoE devices supported Support is included for a broad range of PD ( Powered Devices )

  • IEEE 802.3af, 802.3at PoE/PoE+ ( Alternative A and B )
  • Legacy High Capacitance PDs
  • Cisco legacy VoIP phones and Wireless Access Points
High-Speed Performance Utilizes second generation VDSL2 technology ( ITU-T Recommendation G.993. ). When operating under “Profile 30a”, Perle Ethernet Extenders can provide an aggregate VDSL line rate capability of up to 200 mbps.

Actual distance and performance may vary depending on the type / gauge and condition of the wire used and if required, the amount of power you require across the VDSL Link
Plug and Play operation Perle Ethernet Extenders will automatically configure your VDSL interlink connection. The CO/CPE peer association will be determined automatically by the Ethernet Extender. No need to set CO / CPE VDSL pairing.

Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link.
Link Pass-Through* With Link Pass-Through the state of the 10/100/1000Base-T Ethernet connection is “passed through” the VDSL link to the 10/100/1000Base-T Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early.

Competitive Ethernet extenders without this feature will never detect or report any error conditions.
Interlink Fault Feedback* Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers.
Auto-Negotiation The Ethernet Extender supports auto negotiation on the 10/100/1000Base-T interface.
Auto-MDIX Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100/1000 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout.
Fixed Speed and Duplex Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches.
VLAN Transparent to tagged VLAN ( 802.1Q ) packets.
Transparent to IP Video compression protocols Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG.
Power Strain Relief strap A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration.
Loopback When enabled, will perform a loopback on the copper VDSL Interlink.

*Available on 1 port models.

<
Power eXP-1S1110PE eXP-4S1110PE
Unit Powered by Local power adapter
Provides Power to: Ethernet
Power adapter connector Barrel or terminal block
Input Voltage Range from adapter 46V to 57
Input Voltage Range from VDSL (parasitic) 24 to 57
Universal AC Adapter 56vDC, 75 watt adapter included
Power Connectors 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
Ethernet eXP-1S1110PE eXP-4S1110PE
10/100/1000Base-T Port(s) 1 port RJ45 Shielded 4 port RJ45 Shielded
Auto-MDIX Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance Distance up to 100 meters ( 328 feet ) as per IEEE 802.3
Maximum Frame Size 1522
Type of PoE device Type 2 PSE ( PoE+ ) IEEE 802.3at
PoE PSE Maximum Power (Watts) Refer to the Power Reach Installation Planning Guide
PoE PSE RJ45 Cable Pinout Alternative A ( default ) on all ports:
Pins 3,6 Neg, Pins 1,2 Pos

Alternative B: selectable on port #1:
Pins 7,8 Neg, Pins 4,5 Pos

Legacy Cisco Pre-Standard: selectable on port #1:
Pins 7,8 Pos, Pins 4,5 Neg

VDSL – Interlink eXP-1S1110PE eXP-4S1110PE
RJ45, BNC, Terminal Block

Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.

TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:

  • RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
  • BNC – Coaxial 50 and 75 ohm cable with BNC connector
  • Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ).
VDSL Line Rate/Reach Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG ( 0.5 MM ) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models.
High Speed Asymmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 101 92
1000 305 101 63
1500 457 90 38
2000 610 62 24
2500 762 55 10
3000 914 42 5
3500 1000 35 3
High Speed Symmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 101 101
1000 305 85 101
1500 457 62 47
2000 610 60 29
2500 762 44 14
3000 914 30 7
3500 1000 29 4
Long Reach Symmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 53 44
1000 305 53 43
2500 762 39 18
4000 1219 25 4
5500 1676 17 1.9
7000 2134 8 2.3
7500 2286 7 2.2
8000 2438 5 2.2
Long Reach Asymmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 78 16
1000 305 78 16
2500 762 55 10
4000 1219 31 0.8
5500 1676 20 0.6
7000 2134 11 0.6
7500 2286 10 0.6
8000 2438 8 0.6
Power Budget The amount of available power at the PoE+ PD is dependent on the scenario planned.
Refer to the Power Reach Installation Planning Guide
Indicators eXP-1S1110PE eXP-4S1110PE
Power / TST This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local Ethernet Extender is operating in CO VDSL mode
CPE - remote Ethernet Extender is operating in CPE VDSL mode
ILNK Indicates Link Status and activity on the Interlink (VDSL) port
ETH Indicates link status and activity on Ethernet port(s).
PSE Status This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE;

GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied)

YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :

  • Not connected
  • Has not detected a compliant PD and is not applying power
  • PSE has turned off power for Reset function

OFF — PSE function switch disabled

RED — Blinking: Error Conditions

  • Capacitance too High — 1 blink
  • Resistance too Low or short circuit — 2 blinks
  • Resistance too high or open circuit — 3 blinks

Switches eXP-1S1110PE eXP-4S1110PE
Access Switch settings are accessible through a side opening in the chassis
Rate/Reach Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u) control on Port 1 Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex.

Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

Force Ethernet Speed on Port 1 When Auto-Negotiation switch is disabled, a fixed speed can be forced on port 1 to
100 (Default) or 10
Force Ethernet Duplex on Port 1 When Auto-Negotiation switch is disabled, Full or half Duplex can be forced on port 1 to
Full (Default) or Half
Link Mode* Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.

Link Pass-Through- state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer

Interlink Fault Feedback* Enabled – A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers

Disabled ( Default ) - The state of the VDSL link is not propagated to the 10/100/1000Base-T port

Loopback Enabled – The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its remote peer.

Disabled (Default - Up)

PD Reset ( Port 1 ) When enabled ( down ), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again.

When PD Power Reset is disabled ( default ), loss of VDSL link has no effect on power supplied to the PD.

Environmental Specifications eXP-1S1110PE eXP-4S1110PE
Operating Temperature 0 C to 50 C (32 F to 122 F)
Storage Temperature minimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 meters (10,000 feet)
Current mA 114 @ 56vdc 163 @ 56vdc
Unit Power Consumption watts 6.4 9.1
Heat Output
( BTU/HR )
21.84 31.05
MTBF with power adapter (Hours)** 75,029 72,416
MTBF without power adapter (Hours)** 300,472 262,530
Mounting eXP-1S1110PE eXP-4S1110PE
Wall/Desk Standard
Din Rail Kit Optional
Rack Mount Kit Optional
Product Weight and Dimensions eXP-1S1110PE eXP-4S1110PE
Weight 0.58 Kg, 1.3 lbs 0.61Kg, 1.34 lbs
Dimensions 163 x 116 x 37 mm, 6.4 x 4.6 x 1.46 inches
Packaging eXP-1S1110PE eXP-4S1110PE
Shipping Weight 1.27 Kg, 2.8 lbs 1.3 Kg, 2.86 lbs
Shipping Dimensions 20 x 30 x 7 cm, 7.9 x 11.8 x 2.8 inches
Regulatory Approvals eXP-1S1110PE eXP-4S1110PE
Emissions CISPR 32:2015/EN 55032:2015 (Class A)
IEC/EN 61000-3-2
IEC/EN 61000-3-3
Immunity CISPR 24:2010/EN 55024:2010
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
IEC/EN 61000-4-11
Electrical Safety UL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
CSA C22.2 No. 60950-1
Environmental Reach, RoHS and WEEE Compliant
Other ECCN: 5A991
HTSUS Number: 8517.62.0050
Perle Lifetime warranty

*Available on 1 port models.
**MTBF Calculation model based on MIL-HDBK-217-FN2 @ 30 °C

Extend 10/100/1000 Ethernet across Twisted Pair or Coaxial Cable to a Remote PoE+ device

Extend an Ethernet link to a PoE+ device beyond the 100 meter ( 328 feet ) limit using Ethernet Extenders. Distances of up to 3 km ( 10,000 feet ) can be achieved over twisted pair Cat 5,6 or 7 or Coaxial cable. For long reach applications, the remote extender provides power to PoE devices such as IP cameras and Access Points. A locally attached AC Adapter is used.

eXP-S1110PE PoE+ Gigabit Ethernet Extender Network Diagram to power a remote device
Back to top

Products

Applications

About Perle

Contact Us

How to Buy

Technical Support

Site Map

Legal Information

Privacy & Cookie Policy

Products by Perle

specialix Chase Research

Follow Perle

Copyright © 1996 - 2018 Perle. All Rights Reserved

Contact Us
Products
Applications
How to Buy
Support
About Perle
Privacy & Cookie Policy
Follow Perle

Copyright © 1996 - 2018 Perle. All Rights Reserved