SMI-1110 Managed Media and Rate Converters
10/100/1000Base-T to 1000Base-X Conversion

- 10/100/1000Base-T to 1000Base-X Fiber Media Converters
- Connect 10/100 devices to Gigabit backbone
- Extend network distances up to 160km
- Manage via SNMP, CLI - Telnet/SSH, Internet Browser, or PerleVIEW Centralized Management Package
- Advanced media converter features - Smart Link Pass-Through, Fiber Fault Alert, Auto-MDIX and Loopback
Perle’s advanced line of Managed Gigabit Rate Converting Media Converters, provides transparent and reliable 10/100/1000 ethernet to fiber connections. While providing an economical means of extending your existing copper based network connection, these media converters are SNMP manageable to enable complete control and status viewing of your fiber links.
Perle 10/100/1000 Managed Media Converters come standard with extensive cost and time saving features. In addition, a lifetime warranty and free worldwide technical support make Perle's Managed 10/100/1000 Ethernet Converters the smart choice for IT professionals.
SMI-1110 Managed Gigabit Rate Converting Media Converter Features
QOS ( Quality of Service ) |
|
VLAN Tagging |
|
Unknown Multicast Frame filtering | When enabled, Multicast frames with an unknown destination address are not allowed to egress the port |
Unknown Unicast Frame filtering | When enabled, Unicast frames with an unknown destination address are not allowed to egress the port |
Unidirectional Ethernet | When enabled, provides the ability to restrict port to one-way traffic flow. Used in applications such as unidirectional video broadcasting as well as providing security for ethernet connections in accessible public areas. |
Configuration Mode selection | Select whether to use the on-board DIP switches or the management software for mode selection |
Auto-MDIX | Can manually set Auto or MDIX on the copper port via on-board strap or via the management software. Auto-MDIX (automatic medium-dependant interface crossover) detects the signaling on the copper ethernet interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. The media converter can also correct for wires swapped within a pair. The media converter will adjust for up to 120ns of delay skew between the 1000Base-T pairs. |
Converter Information |
|
DIP switch settings | View hardware DIP switch settings |
Selectable Max Packet Size | Set max packet size to 1522 / 2048 or 10,240 ( default ) |
10BaseT Extended Distance | Normal/extended – default Normal. By configuring as “extended”, the 10baseT receiver sensitivity is increased providing the possibility of a 10BaseT connection greater than 100m. |
Auto Copper downshift | Automatically detects a 2-pair cable environment and downshifts operation of the link to 100 Mb/s. Configure the number of times ( 0-8 ) that the PHY will attempt to establish a successful Gigabit link before attempting to “downshift” as an auto-negotiating 10/100 device. Setting # of attempts to 0 ( default ) disables the feature. |
Virtual Cable Test | A test that enables the detection of potential copper cabling issues such as pair polarity pair swaps and excessive pair skew as well as any opens, shorts or any impedance mismatch. Will report the distance in the cable to the open or short. |
Port Control | Enable or disable individual fiber or copper port on the converter |
Copper Port Status |
|
Fiber Port Status |
|
Control |
|
Detailed port statistics | To assist in troubleshooting copper and fiber links, an extensive list of ingress and egress counters for both copper and fiber ports are available. These statistics can be viewed locally via the management module or from a central SNMP NMS on the network |
Auto-Negotiation (802.3u) |
The media converter supports auto negotiation. The 1000Base-X fiber interface negotiates according to 802.3 clause 37. The 10/100/1000Base-T negotiates according to 802.3 clause 28 and 40. The 1000Base-X will link up with its partner after the highest common denominator (HCD) is reached and the copper has linked up with its partner. The 1000Base-X will continue to cycle through negotiation transmitting a remote fault of offline (provided this is enabled through the switch setting) until the copper is linked up and the HCDs match. The media converter supports auto-negotiation of full duplex, half duplex, remote fault, full duplex pause, asymmetric pause and Auto MDI-X. |
Smart Link Pass-Through | When the Link Mode switch is placed into Smart Link Pass-Through mode, the copper ethernet port will reflect the state of the 1000Base-X media converter port. This feature can be used whether fiber auto-negotiation is enabled or disabled. |
Fiber Fault Alert | With Fiber Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fiber auto-negotiation is disabled. |
Pause (IEEE 802.3xy) | Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100/1000Base-T connection and 1000Base-X fiber connection. |
Duplex | Full and half duplex operation supported. |
Jumbo Packets | Transparent to jumbo packets up to 10KB. |
Remote Loopback | Capable of performing a loopback on the 1000Base-X fiber interface. |
SMI-1110 Advanced Management Features
Enterprise and carrier-grade security is available through the support of strong authentication systems such as TACACS+, RADIUS and LDAP. Secure in-band access is assured via SNMPv3, SSH CLI and secure HTTPS Internet browser.
SNMP |
|
Telnet / SSH CLI access | In-band command line access via Telnet or SSH application |
Internet Browser access |
|
Console port CLI access |
Out-of-band command line access via Cisco compatible RJ45 serial console port using common “rolled” CAT5 cable. Console port can be enabled ( default ) or disabled |
Concurrent management sessions | Run multiple management sessions simultaneously for multiple users |
Inactivity timeout | Protect secure management sessions by setting an inactivity timeout value |
Alert event reporting |
Alert level events are stored in the local event log and sent as:
|
Advanced IP feature set |
|
Advanced Management User Authentication with primary and secondary server support |
|
Advanced Management User Authorization and Accounting |
|
Encryption |
|
Access Control List | An access control list can be created which can filter out only those workstations that are authorized to access the management resources. Filter on IP and/or Ethernet MAC addresses |
Network Services Filter | Enable only those network services on the management module that are allowed on your network ( Telnet, SSH, HTTP, HTTPS, SNMP ) |
Firmware download | Update the latest level firmware for management and media converter modules via TFTP or PerleVIEW |
Hardware Specifications
Media Converter Module Indicators | |
---|---|
Power / TST | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode. |
Fiber link on / Receive activity (LKF) | This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received. |
Copper link on / Receive activity (LKC) | This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is on and flashes with a 50% duty cycle when data is received. |
Fiber Duplex (FDF) | This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operatinal in full duplex mode. The LED is off when in half duplex. |
Copper Duplex (FDC) | This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operatinal in full duplex mode. The LED is off when in half duplex. |
10/100/1000 Speed | This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is orange when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps. |
Management Module Indicators / reset | |
Power | Blinking green during startup cycle Steady green: module has power and is ready Red : error |
ALM | Red alarm indicator activated when an alert event occurs |
LKC | Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data |
100/1000 | Green - 1000 Mbps link Yellow - 100 Mbps link Off - 10 Mbps or no Link |
Reset button | Recessed pinhole button resets module |
Connectors | |
10/100/1000Base-T | RJ45 connector 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. 4 pair CAT5 UTP cable for Gigabit. Magnetic Isolation1.5kv |
Management ethernet port | 10/100/1000Base-T - RJ45 Auto- MDI/MDIX |
Management console port | RS232 Serial RJ45 - Cisco pinout for use with standard CAT5 "rolled cable" (crossover) 9600 to 115k bps 7/8 bits Odd,even, no parity 1/2 stop bits Hardware/software flow control DCD/DSR monitoring |
Filtering | |
Filtering | 1024 MAC Addresses |
Frame Specifications | |
Buffer | 1000 Kbits frame buffer memory |
Size | Maximum frame size of 10,240 bytes -- Gigabit Maximum frame size of 2048 bytes -- Fast Ethernet |
Switches - accessible through a side opening in the chassis | |
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities.
Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
Link Mode | Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter.
Normal (Default – Up) With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link. Smart Link Pass Through (Down) With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. |
Fiber Fault Alert | The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled
Enabled (Default - Up) Disabled (Down) |
Remote Loopback | The media converter can perform a loopback on the 1000Base-X fiber interface.
Disabled (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface. |
Auto-MDIX (Strap) | If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
Speed Copper | 100 (Default) 10 |
Duplex Copper | Full (Default) Half |
Duplex Fiber | Full (Default) Half |
Power | |
Input Supply Voltage | (12 vDC Nominal) |
Current | 0.34amps at 12vdc |
Power Consumption | 4.1watts |
Power Connector | 5.5mm x 9.5mm x 2.1mm barrel socket |
Power Adapter | |
Universal AC/DC adapter | 100-240v AC, regulated DC adapter included |
Environmental Specifications | |
Operating Temperature | 0 C to 50 C (32 F to 122 F) |
Storage Temperature | minimum range of -25 C to 70 C (-13 F to 158 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output (BTU/HR) |
14 |
MTBF (Hours) | 238,087 without power adaptor 164,883 with power adaptor Calculation model based on MIL-HDBK-217-FN2 @ 30 °C |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.722 kg |
Dimensions | 175 x 145 x 23 mm |
Packaging | |
Shipping Weight | 1.2 kg |
Shipping Dimensions | 300 x 200 x 70 mm |
Regulatory Approvals | |
Emissions | FCC Part 15 Class A, EN55022 Class A |
CISPR 22 Class A CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 |
UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
|
CE | |
Laser Safety | EN 60825-1 |
Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. | |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A992 |
HTSUS Number: 8517.62.0020 | |
CCATS: G134373 | |
Perle Limited Lifetime Warranty |
Select a Model to obtain a Part Number - Managed Stand-alone Media Converters - 10/100/1000 to Fiber
Model |
Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Core Size (um) |
Modal Bandwidth (MHz* Km) |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||||
SMI-1110-M2SC05 | Dual SC |
1000Base-SX |
-9.5 |
-4.0 |
-17.0 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
||||||||||
50 |
400 |
500 m (1,640 ft) |
||||||||||
50 |
500 |
550 m (1,804 ft) |
||||||||||
50 |
2000 |
1000 m (3281 ft) |
||||||||||
SMI-1110-M2LC05 | Dual LC |
1000Base-SX |
-9.5 |
-4.0 |
-17.0 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
||||||||||
50 |
400 |
500 m (1,640 ft) |
||||||||||
50 |
500 |
550 m (1,804 ft) |
||||||||||
50 |
2000 |
1000 m (3281 ft) |
||||||||||
SMI-1110-M2ST05 | Dual ST |
1000Base-SX |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
||||||||||
50 |
400 |
500 m (1,640 ft) |
||||||||||
50 |
500 |
550 m (1,804 ft) |
||||||||||
50 |
2000 |
1000 m (3281 ft) |
||||||||||
SMI-1110-M2SC2 | Dual SC |
1000Base-LX |
-6.0 |
0.0 |
-17.0 |
-0.0 |
11 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
50 |
500 |
1000m (3280ft) |
||||||||||
SMI-1110-M2ST2 | Dual ST |
1000Base-LX |
-6.0 |
0.0 |
-17.0 |
-0.0 |
11 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
50 |
500 |
1000m (3280ft) |
||||||||||
SMI-1110-M2LC2 | Dual LC |
1000Base-LX |
-9.0 |
-1.0 |
-19.0 |
-1.0 |
10 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
50 |
500 |
1000m (3280ft) |
||||||||||
SMI-1110-S2SC10 | Dual SC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m (1,804 ft) |
50 |
400 |
550 m (1,804 ft) |
||||||||||
50 |
400 |
550 m (1,804 ft) |
||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
|||||||||
SMI-1110-S2LC10 | Dual LC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m (1,804 ft) |
50 |
400 |
550 m (1,804 ft) |
||||||||||
50 |
400 |
550 m (1,804 ft) |
||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
|||||||||
SMI-1110-S2ST10 | Dual ST |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m (1,804 ft) |
50 |
400 |
550 m (1,804 ft) |
||||||||||
50 |
400 |
550 m (1,804 ft) |
||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
|||||||||
SMI-1110-S2SC40 | Dual SC |
1000Base-EX |
-2.0 |
2.0 |
-23.0 |
-3.0 |
21.0 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
SMI-1110-S2LC40 | Dual LC |
1000Base-EX |
-3.0 |
2.0 |
-23.0 |
-3.0 |
20.0 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
SMI-1110-S2ST40 | Dual ST |
1000Base-EX |
-2.0 |
2.0 |
-23.0 |
-3.0 |
21.0 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
SMI-1110-S2SC70 | Dual SC |
1000Base-ZX |
-2.0 |
5.0 |
-23.0 |
-3.0 |
21.0 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
SMI-1110-S2LC70 | Dual LC |
1000Base-ZX |
0.0 |
5.0 |
-23.0 |
-3.0 |
23.0 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
SMI-1110-S2ST70 | Dual ST |
1000Base-ZX |
-2.0 |
5.0 |
-23.0 |
-3.0 |
21.0 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
SMI-1110-S2SC120 | Dual SC |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9 |
32.0 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
SMI-1110-S2LC120 | Dual LC |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9 |
32.0 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
SMI-1110-S2ST120 | Dual ST |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9 |
32.0 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
SMI-1110-S2SC160 | Dual SC |
1000Base-ZX |
2.0 |
5.0 |
-34.0 |
-9 |
36.0 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
SMI-1110-S2LC160 | Dual LC |
1000Base-ZX |
2.0 |
5.0 |
-34.0 |
-9 |
36.0 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
SMI-1110-S2ST160 | Dual ST |
1000Base-ZX |
2.0 |
5.0 |
-34.0 |
-9 |
36.0 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
Single Fiber Models Recommended use in pairs
Model |
Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Core Size (um) |
Modal Bandwidth (MHz* Km) |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||||
SMI-1110-M1SC05U | Single SC |
1000Base-BX-U |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1310 / 1550 |
MMF |
62.5 |
500 |
500 m (1,640 ft) |
50 |
500 |
500 m (1,640 ft) |
||||||||||
SMI-1110-M1SC05D | Single SC |
1000Base-BX-D |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1550 / 1310 |
MMF |
62.5 |
500 |
500 m (1,640 ft) |
50 |
500 |
500 m (1,640 ft) |
||||||||||
SMI-1110-S1SC10U | Single SC |
1000Base-BX-U |
-9.0 |
-3.0 |
-20.0 |
-3.0 |
11.0 |
1310 / 1490 |
SMF |
** |
- |
10 km (6.2 mi) |
SMI-1110-S1SC10D | Single SC |
1000Base-BX-D |
-9.0 |
-3.0 |
-20.0 |
-3.0 |
11.0 |
1490 / 1310 |
SMF |
** |
- |
10 km (6.2 mi) |
SMI-1110-S1SC20U | Single SC |
1000Base-BX-U |
-8.0 |
-3.0 |
-22.0 |
-3.0 |
14.0 |
1310 |
SMF |
** |
- |
20 km (12.4 mi) |
SMI-1110-S1SC20D | Single SC |
1000Base-BX-D |
-8.0 |
-3.0 |
-22.0 |
-3.0 |
14.0 |
1490 |
SMF |
** |
- |
20 km (12.4 mi) |
SMI-1110-S1SC40U | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-23.0 |
-3.0 |
20.0 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
SMI-1110-S1SC40D | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-23.0 |
-3.0 |
20.0 |
1490 |
SMF |
** |
- |
40 km (25 mi) |
SMI-1110-S1SC80U | Single SC |
1000Base-BX-U |
-2.0 |
3.0 |
-26.0 |
-3.0 |
24.0 |
1510 |
SMF |
- |
- |
80 km (50 mi) |
SMI-1110-S1SC80D | Single SC |
1000Base-BX-D |
-2.0 |
3.0 |
-26.0 |
-3.0 |
24.0 |
1590 |
SMF |
- |
- |
80 km (50 mi) |
SMI-1110-S1SC120U | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-34.0 |
-9 |
31.0 |
1510 |
SMF |
- |
- |
120 km (75 mi) |
SMI-1110-S1SC120D | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-34.0 |
-9 |
31.0 |
1590 |
SMF |
- |
- |
120 km (75 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*A mode-conditioning adapter as specified by the IEEE standard, is required regardless of the span length. Note how the mode conditioning adapter for 62.5-um fibers has a different specification from the mode-conditioning adapter for 50-um fibers.
**ITU-T G.652 SMF as specified by the IEEE 802.3z standard.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |