S-110-XT Industrial Temperature Media Converters
10/100Base-TX to 100Base-X Conversion

- 10/100Base-TX to 100Base-X Fiber Media Converters
- Extend network distances up to 20km for industrial Ethernet equipment
- Advanced features - Link Pass-Through, Far-End Fault, Auto-MDIX and Loopback
- -40°F to +167°F (-40°C to +75°C) extended temperature support
- Terminal block power connector
The S-110-XT Industrial Temperature Media Converters address the need for transparently connecting 10/100 Ethernet equipment that operate in extreme temperatures to fiber optic cable. The S-110-XT Media Converters will operate in industrial grade temperatures of -40°F to +167°F (-40°C to +75°C). Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based media converter. Boasting this extended temperature feature along with a rugged steel casing, the S-110-XT Media Converter provides an economical path to extend the distance between two industrial devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.
Network Administrators can "see-everything" with Perle's advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Far End Fault, and Remote Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle's S-110-XT Industrial Temperature 10/100 Media Converters the smart choice for IT professionals.
S-110-XT Industrial Temperature Media Converter 10/100 to Fiber Features
Auto-Negotiation (802.3u) | The media converter supports auto negotiation on the 10/100Base-TX interface. |
Auto-MDIX | Auto-MDIX (automatic medium-dependant interface crossover) detects the signaling on the UTP interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. With Auto-MDIX enabled, either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. |
Link Pass-Through |
With Link Pass-Through the state of the UTP
receiver is passed to the fiber transmitter
to make the media converter appear transparent
to the end devices that are connected. In addition
if Far-End Fault is enabled the media converter
can turn off the 10/100Base-TX transmitter when
a FAR-End Fault is received. Using Link Pass-Through with Far-End Fault minimizes data loss when a fault occurs. Should a fault occur, the end devices have the indication of a failure available to them making trouble shooting easier. |
Far-End Fault (FEF) |
The media converter implements the 802.3 standard for Far-End Fault for the indication and detection of remote fault conditions on the 100Base-X fiber connection. With Far-End Fault enabled the media converter transmits the Far-End Fault Indication over the 100Base-X fiber connection whenever a receive failure is detected on the 100Base-X fiber connection. The media converter continuously monitors the100Base-X fiber connection for a valid signal. The action the media converter takes on receiving a Far-End Fault Indication is dependent on the Link Pass-Through switch setting. |
Pause (IEEE 802.3xy) | Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100Base-TX copper connection. |
VLAN | The media converter is transparent to VLAN tagged packets. |
Remote LoopBack | The media converter is capable of performing a loopback on the fiber port. |
Hardware Specifications
Power | |
---|---|
Input Supply Voltage | 6 - 30 vDC, unregulated (12 vDC Nominal) |
Current | 175 mA |
Power Consumption | 2.1 watts |
Power Connector | 2-pin fixed terminal block |
Indicators | |
Power / TST | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode. |
Fiber link on / Receive activity (LKF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received. |
Copper link on / Receive activity (LKC) | This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received. |
Fiber Duplex (FDF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is operatinal in full duplex mode. The LED is off when in half duplex. |
Copper Duplex (FDC) | This green LED is operational only when power is applied. The LED is on when the 10/100Base-TX link is operatinal in full duplex mode. The LED is off when in half duplex. |
10/100 Speed | This green LED is operational only when power is applied. The LED is on when the speed of the copper Ethernet port is running at 100 MBPS. The LED is off when in 10 MBPS |
Switches - accessible through a side opening in the chassis | |
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter
uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to
advertise full duplex. Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
Link Pass Through | Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter. When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on. Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface. |
Far-End Fault (FEF) | Enabled (Default) - The media converter transmits the Far-End
Fault Indication over the 100Base-X fiber connection whenever a receive
failure is detected on the 100Base-X fiber connection. The media converter
continuously monitors the100Base-X fiber connection and clears the Far-End
Fault Indication condition when a valid signal is received. Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection. |
Remote Loopback | The media converter can perform a loopback on the 100Base-X fiber
interface. Disabled (Default - Up) Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface. |
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the
HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u)
is disabled the Media converter will use the RX Energy method on the 100Base-TX
interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
Speed Copper | 100 (Default) 10 |
Duplex Copper | Full (Default) Half |
Duplex Fiber | Full (Default) Half |
Connectors | |
100Base-TX | RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable |
Magnetic Isolation | 1.5kv |
Filtering | |
Filtering | 1024 MAC Addresses |
Frame Specifications | |
Buffer | 512 Kbits frame buffer memory |
Size | Maximum frame size of 2048 bytes |
Environmental Specifications | |
Operating Temperature | -40 C to 75 C (-40 F to 167 F) |
Storage Temperature | -40 C to 85 C (-40 F to 185 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output (BTU/HR) |
7.2 |
MTBF (Hours)* | 607,001 |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.3 kg, 0.66 lbs |
Dimensions | 120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches |
Packaging | |
Shipping Weight | 0.425 kg, .9 lbs |
Shipping Dimensions | 150 x 210 x 40 mm, 5.9 x 11 x 2.8 inches |
Regulatory Approvals | |
Emissions | FCC Part 15 Class B, EN55022 Class B |
CISPR 22 Class B CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 |
UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
|
CE | |
Laser Safety | EN 60825-1 Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A991 |
HTSUS Number: 8517.62.0020 | |
Perle Limited Lifetime Warranty |
*Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Fast Ethernet to IP Cameras |
---|
Connect 10/100 IP Cameras to Fast Ethernet Backbone Stand-alone Extended Temperature Media Converters are placed at the remote end connecting cameras with copper interfaces to fiber optic cabling. The fiber can extend the distance up to 20 kilometers using single mode or multimode fiber back to a control center. A media converter chassis located in the data closet at the control center accepts the fiber signal, converts it, and connects to the copper equipment at the main site. ![]() |
Fast Ethernet Fiber to Wireless Access Points |
Connect 10/100 Wireless Access Points to Fast Ethernet Backbone When AP’s are used in industrial environments where extremely high or low temperatures are a concern, Stand-alone Extended Temperature Media Converters are placed at the remote end connecting APs with copper interfaces to fiber optic cabling. The fiber can extend the distance up to 20 kilometers using single mode or multimode fiber back to a control center. A media converter chassis located in the data closet at the control center accepts the fiber signal, converts it, and connects to the copper equipment at the main site. ![]() |
Bridge 10/100 Devices to gigabit Backbone |
Connect 10/100 devices to Gigabit Backbone ![]() |
Single Mode / Single Fiber |
Connect copper ports over a single fiber strand ( also referred to as “Bi-Directional” BiDi ) ![]()
However, to reduce costs, or where there are limits on available fiber, WDM technology may be utilized. WDM uses separate transmit and receive frequencies to communicate on a single fiber strand. WDM technology relies on the fact that optical fibers can carry many wavelengths of light simultaneously without interaction between each wavelength. Thus, a single fiber can carry many separate wavelength signals or channels simultaneously. So remember, if Single Strand fiber is used, you will need an “Up” Media Converter on one side and a “Down” Media Converter on the other for copper to fiber conversion. |
Select a Model to obtain a Part Number - S-110-XT Industrial Temperature Media Converter 10/100 to Fiber
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110-M2ST2-XT | Dual ST |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-M2SC2-XT | Dual SC |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-M2LC2-XT | Dual LC |
100Base-FX |
-20.0 |
-12.0 |
-30.0 |
-14.0 |
10.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-S2ST20-XT | Dual ST |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2SC20-XT | Dual SC |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2LC20-XT | Dual LC |
100Base-LX |
-15.0 |
0.0 |
-34.0 |
-5.0 |
19.0 |
1310 |
SMF |
20 km (12.4 mi) |
Single Fiber Models Recommended use in pairs
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110-S1SC20U-XT | Single SC |
100Base-BX |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km (12.4 mi) |
S-110-S1SC20D-XT | Single SC |
100Base-BX |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km (12.4 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*Based on use with 62.5/125 micron multimode fiber.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |
04030674 | Extended Temperature USA power adapter for 12 Volt Industrial Temperature Media Converter |
04030671 | Extended Temperature UK power adapter for 12 Volt Industrial Temperature Media Converter |
04030672 | Extended Temperature EU power adapter for 12 Volt Industrial Temperature Media Converter |
04030675 | Extended Temperature SA power adapter for 12 Volt Industrial Temperature Media Converter |
04030676 | Extended Temperature AUS power adapter for 12 Volt Industrial Temperature Media Converter |